From ETABS to SAP2000

This article explains how to send a model from ETABS to SAP2000, using BIM Expert.

1. Preparation in ETABS

If you simply want to have the geometry & loads model in SAP2000, without further BIM workflows, analysis in ETABS is not required.

2. Send the ETABS model to SAP2000

2.1 From ETABS to BIM Expert

In the Model tab, select ‘Import’. Next, choose the source software manufacturer, namely ‘Computer and Structures, Inc’ (CSI) . Click  to continue. Choose ‘ETABS’. Alternatively, models can be sent to BIM Expert directly within ETABS (Tools > BIM Expert), but you first need to add BIM Expert as a plug-in to ETABS.

2.2.1 Settings

Select your ETABS version, and were the model is coming from:

• A running instance – that means, the model is currently open in ETABS
• An existing model – click ‘Browse… ‘ to open your file browser, go to the model location and select the model (an .edb file)

On top of the geometry conversion, you can also consider loads and results in points, bars & plates.  Bar results are the most used and relevant ones, so only considering the bar results is enough. Plate results can be huge amount of data, that is currently not used any further. Next, the ETABS material and sections must be mapped with BIM Expert ‘s materials and section. BIM Expert will try to find as many automatic mapping matches as possible. In case all sections and materials find a match, you will not see any dialogs for mapping.

2.2.2 Material mapping

Database materials such as steel (e.g. S235, ASTM-Grades), concrete (e.g. C25/30, M50) and timber (e.g. C24, D50, GL28c) are mapped automatically. In some cases, the match is not automatically found, because the name differs (S355-link instead of S355). In that case, you can select the correct material from the database. Tip: When searching an item in the database, type the first letters of the name to find it more quickly.

2.1.3 Section mapping

Database sections (such as I, H, UB, UC, W, C, U, O, ☐ and L sections) are mapped automatically. In some cases, the match is not automatically found, because the name differs  (e.g. name is HEB300 – S235 instead of HEB300). In that case, you can select the correct cross-section from the database. Tip: When searching an item in the database, type the first letters of the name to find it more quickly. Parametric sections (e.g. rectangles, circle, trapezium, …) are not in the database. They should always be added as new.

2.1.4 Loads mapping

If you opted to consider the loads during export, the ETABS load combinations need to be categorized. Each valid ETABS combination must be categorized into Eurocode or American combinations. Use the checkbox ‘Use categories according to Limit States’ to switch between European and American combination categories. Depending on the design code, you must map each combination with either

• Eurocode Limit States
  • ULS – Ultimate Limit State Combinations: Fundamental (FC), Seismic (SC), Fire (FI) or Accidental (AC)
  • SLS – Serviceability Limit State Combinations: Rare (RC), Frequent (FC) or Quasi-Permanent (QP)
  • Custom
• Armerican
  • Strength
  • Service
  • Custom

On hoovering with the mouse over the combination’s name, you can see the build up of the combination (e.g. 1.35 DL + 1.50 LL). Use SHIFT and CTRL commands as in Windows to select one or multiple items. For example, to select all, use ‘CTRL+A’ and then, select the “+” button in the corresponding column. Envelope combinations and dynamic seismic combinations are cannot be matched, as this is not supported by BIM Expert. These types of combinations are considered non-valid and will be greyed out. Static seismic combinations can be mapped. Remark: If you cancel that load mapping dialog, combinations are neglected and the conversion proceeds.

2.1.5 Reporting

In case of severe incidences, you get a report of the incidences. It usually concerns load cases or element behavior that are not supported by BIM Expert. Click ‘Continue’ to proceed anyway. The model is now in BIM Expert.

2.2 From BIM Expert to SAP2000

In the Model tab, select ‘Export’. Next, choose the destination software manufacturer, namely ‘Computer and Structures, Inc’ (CSI) . Click  to continue.

Choose ‘SAP2000’

2.2.1 Settings

Select your SAP2000 version, the destination and analysis model.  The destination can be either:

• To a new empty model in a new instance – after the file is loaded you immediately will be prompted to save the file
• To current instance and new empty model

SAP2000 will launch automatically in case of ‘new instance’ choice.

Next, the BIM Expert sections and materials must be mapped with SAP2000’s section and materials. BIM Expert will try to find as many automatic mapping matches as possible. In case all sections and materials find a match, you will not see any dialogs for mapping.

2.2.2 Material mapping

In a new file, SAP2000 only has 2 materials present: Steel S355 and Concrete 30/37. Chances are real that you see the material mapping dialog.  If you cannot find a suited counterpart in the SAP2000 model, the material can be added as new.

2.1.3 Section mapping

A new SAP2000 model has no cross-sections. So all will be added as new.

 

3. Final steps in SAP2000

Depending on the chosen destination: launch SAP2000 and open the file. Or continue working in the open version of SAP2000.